SPARES RACING QUADCOPTER

Sort By:  
  • L506 NAZ32 FULL FLIGHT CONTROL BOARD (NAZE32 FULL FLIGHT CONTROL BOARD)

    The popular Naze32 is here! This is the Full version of the Naze32 board.  Initially designed for use with small to mid-sized multirotor craft, it has become the go-to controller for a host of Multirotor projects and propheads.

    BE AWARE BOARD COLOURS DO VARY FROM BATCH TO BATCH

    Current colour: White

    Current version: Rev6B

    The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration.

    Features:

    • Flexible motor outputs, support various airframe types:
    • Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
    • Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum satellite receivers.
    • Built in FrSky telemetry inverter (shared w/main port)
    • Battery voltage monitoring
    • Modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
    • 3-axis magnetometer (HMC5883L)
    • Pressure sensor (MS5611)
    • Onboard MicroUSB for setup and configuration
    • Bright LEDs
    • MultiWii-based configuration software for easy setup
    • rev6b hardware

    Specs:
    36x36 mm (30.5mm Mounting)
    5.3 grams (no headers, 7.3 grams with)
    2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6500)

    3-axis magnetometer (HMC5883L)

    Pressure sensor (MS5611)

    Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line

    Packaged with:

    • 90 degree header pins
    • Straight header pins
    • Breakout cable
    Add to Cart
    R1,009.00
  • L532 800TVL CAMERA 5-20V 2.8MM WIDE ANGLE LENS (800TVL CAMERA 5-20V 2.8MM WIDE ANGLE LENS)

    This is a colour 800tvl high resolution board camera for FPV. This camera uses a high sensitivity sensor with a resolution up to 800TVL. It can support power DC5V or DC12V. There is 30cm servo cable included which can be used to connect to the VTx directly. Size 38x38mm, you can cut the edge and make it into a camera of 32x32mm. Light weight at 13g.

    Specs :

    • 1/3" High Sensitivity CMOS sensor
    • Auto color to black function
    • Up to 800TVL high resolution
    • Auto White Balance
    • Auto AGC
    • Low illumination: 0.05lux
    • Low current: 55mA
    • DC5V~DC20V
    • 2.8mm lens
    Add to Cart
    R479.00
  • L540 MN2206 T MOTOR 2000 KV (T-MOTOR 2000KV)
    KV2000
    Configuration 12N14P
    Stator Diameter 22mm
    Stator Length 6mm
    Shaft Diameter 3mm
    Motor Dimensions (Dia.*Len) Φ27×18.5mm
    Weight (g) 30g
    ldle current(10)@10v(A) 0.A
    No.of Cells(Lipo) 2-3S
    Max Continuous current(A)180S 18A
    Max Continuous Power(W)180S 180W
    Max. efficiency current (2-5A)>80%
    Internal resistance 82mΩ
    Add to Cart
    R474.00
  • L507 CC3D EVO FLIGHT CONTROL BOARD (CC3D EVO FLIGHT CONTROL BOARD)
    The CC3D EVO provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes.  Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.Software support for Windows, Mac and Linux.Direct high speed USB support with no drivers required, a truly plug and play device.Spektrum satellite receiver support.Futaba S-BUS hardware support.Innovative Flexi-port technology for superior port flexibility.4Mbits on-board EEPROM for configuration storage. FlexiportCopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. Superior user experienceOpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it! Sensors and Components3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.Simultaneous support for multiple receivers.ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channelsMainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellitesFlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)10 PWM outputs to servos or ESC’s, or for camera stabilizationCamera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.Onboard USB connectivity for easy configuration.USB and serial telemetry and configuration Supported by powerful OpenPilot GCS4 Mbit onboard memory3C Quaternion based complementary filter running at 500Hz Package included:1 x CC3D EVO Flight Controller1 x 8p wire rod1 x 4p expansion path1 x Damping Board 1 x Antenna Base
     
    Add to Cart
    R377.00
  • L490 DYS BE1806 BRUSHLESS MOTOR 2300KV (BRUSHLESS MOTOR 2300KV)

    The DYS BE1806 multirotor motor is ideal for starting in miniquad racing and comes complete with mounting bolts, a choice of prop adapters and 150mm power leads with 2mm bullet connectors.
    Specifications:
    Rpm/V: 2300kv
    Dimensions: 23 × 21mm
    Shaft: 2mm
    Voltage: 2S~3S (7.4v to 11.1v)
    Weight: 24g
    Watts: 89W
    Max Current: 8A
    ESC: 10amp to 12amp
    Suggested Prop: 5x3(3S 11.1v) ~ 6x2 (2S 7.4v) 
    Motor Mount Holes: M2 x 12mm /16mm
    Add to Cart
    R301.00
  • L511 ZMR250 PDB V2 4 LAYERS (L511 ZMR250 PDB V2 4 LAYERS)

    4 layer ZMR250 PDB V2

    LED Switch

    CC3D or Naze32 can easily be plugged into the board using the provided hardware.

    Supports 25V and 80A

    Add to Cart
    R279.00
  • L500 FV008 5.8G CIRCULAR POLARIZED SMA ANTENNA SET (5.8G CIRCULAR POLARIZED SMA ANTENNA SET)
    • Tx antennas is a circular-polarized omni antenna with three lobes
    • Rx antennas is a circular-polarized omni antenna with four lobes
    • SWR: 1.2.:1, Tuned for 5645-5945Mhz
    • Polarization: RHCP, Right Hand Circular Polarization
    • Connector: SMA
    • Weight: Tx Antennas10.3g Rx Antennas 11.5g
    • Package Weight: 63.3g
    Add to Cart
    R255.00
  • L508 MATEK 36 X 36 PDB WITH 5V AND 12V BEC 3A (L508 MATEK 36 X 36 PDB WITH 5V AND 12V BEC 3A)

    The Matek PDB has been engineered to provide the highest possible performance and reliability in a 36*36mm & 4 layers PCB. The HUB distributes power from a battery pack to 4 ESCs, as well as providing synchronised & regulated DC outputs for powering cameras, servos, video transmitters, LEDs, etc. Batteries may range from 3S to 6S LiPo. The HUB also features convenient solder bridge of various voltage for camera & video TX.

    General

    • Input voltage range (3S-6S operation): 9 - 26VDC
    • Regulated 5V and 12V outputs
    • LED power indicators ( 5V & 12V outputs )
    • 4 ESC outputs

    Outputs

    • Continuous current: 20A per output
    • Peak current (10 seconds/minute): 25A per output

    BEC 5V output:

    • Designed for RC Receivers, Flight controllers, OSD, and Servos.
    • DC/DC synchronous buck regulator, Efficiency is up to 95%.
    • Voltage: 5.0 +/- 0.1VDC
    • Continuous current: 3 Amps
    • Short-circuit tolerant (10 seconds/minute)
    • LED (indicates voltage is in regulation)

    BEC 12V output:

    • The battery should be 4S~6S LiPo
    • Standard output designed to power cameras and video transmitters,etc. 
    • Voltage: 12.0 +/- 0.2VDC
    • Continuous current: 2 Amps (Max.3A 10s/minute)
    • Short-circuit tolerant (10 seconds/minute)
    • LED (indicates voltage is in regulation)

    CAM & VTX voltage bridge

    • 3S operation. choose “VCC” for 12V camera & 12V VTX, VCC=Battery Voltage.
    • 4~6S operation, choose “12” for 12V camera & 12V VTX
    • 3~6S operation, choose “5” for 5V camera
    • Video pass through from the “CAM” pad to the “VTX” pad

    Physical

    • Dimensions: 36 x 36mm
    • Weight: 6g 
    Add to Cart
    R129.00
  • L493 FY007 PDB 5V AND 12V BEC AND LED SWITCH (L493 PDB 5V AND 12V BEC AND LED SWITCH)
    Same size and hole with Naze32 flight controller
    With 2 BEC output: 5V and 12V
    With LED control switch
    Input voltage: 2-6S
    Weight:6g
    Add to Cart
    R126.00
  • L510 DIATONE ZMR250 PDB (L510 DIATONE ZMR250 PDB)
    Weight: about 35g
    Compare with the previous versions it supports higher currents. Plus more flexible arm mount holes. 5v linear BEC built in. 
     
    Package included:
    1 x ZMR250 V2.1 PCB Board
    Insulation washers
    4 x LED strips
    Add to Cart
    R98.00
  • L495 AT009 5CM SMA PLUG TO RIGHT ANGLE SMA JACK PIGTAIL CABLE (5CM SMA PLUG TO RIGHT ANGLE SMA JACK PIGTAIL CABLE)
    1 x SMA Female to SMA 90 degree male 5cm RF Adapter Pig Tail
     
    The perfect way extend your ant from your vtx and securely mount the antenna to your quad frame. Also protects your vtx antenna plug from being ripped off in a crash.
    Add to Cart
    R77.00
  • L491 FLY029 MINI ADJUSTABLE UBEC / STEPDOWN REGULATOR 12V OR 5V (MINI ADJUSTABLE UBEC / STEPDOWN REGULATOR 12V OR 5V)

    Perfect for mini quads where space is an issue.  This step down regulator can be used to power your flight controller with 5v or even set it to 12v to power your FPV gear.  They are so small you could use two.

    Step-Down Module

    Input Volt: 4.75V-23V

    Output Volt: 1.0V-17V

    Output Amp: Peak Amp 3A, Continuous 1.8A.

    Size: 11 * 17 * 3.8mm

    Conversion efficiency: 96% (maximum)

    Switching frequency: 340KHz

    Output ripple: 30mV (no load)

    Load Regulation: ± 0.5%

    Voltage Regulation:± 2.5%

    Working temperature: -40  to + 85

    Add to Cart
    R68.00
  • L515 DAL "UNBREAKABLE 6045 V2 BULLNOSE PROPS (L515 DAL "UNBREAKABLE 6045 V2 BULLNOSE PROPS)

    The NEW DALRC 6045 V2 bull nose props are now even better.  Improved performance and strength.

    Specs

    • 5mm hole
    • 6inch diameter
    Package Includes
    2 x CW Propeller
    2 x CCW Propeller
    Add to Cart
    R53.00
  • L492 FY005 BLACK NYLON FLIGHT CONTROLLER 10MM MOUNTING PACK (BLACK NYLON FLIGHT CONTROLLER 10MM MOUNTING PACK)

    4 x Black Nylon M3 male/female 10mm Standoff

    4 x Black Nylon nuts

    4 x Black Nylon screws

    Add to Cart
    R35.00
  • L513 PROP ADAPTER FOR BE1806 (PROP ADAPTER FOR BE1806)
    Right hand threaded prop adapter for DYS BE1806 R
    Add to Cart
    R35.00
  • L541 TRANSPARENT PROPELLERS 5X3 (TRANSPARENT PROPELLER 5X3)
    Clear 5030 Propellers for night flying LED illuminated set of 4
    (2 xCW and 2 x CCW) 4pcs Per Bag
    Add to Cart
    R28.00
  • L522 DIATONE PROPELLERS 5X3 (L522 DIATONE PROPELLERS 5X3)
    5030 Propellers packaged in a set of 4
    Only available in White.
    Add to Cart
    R27.00
Per Page      1 - 20 of 20